PLUMBING BASICS: AN ESSENTIAL FOR WHEN INSTALLING A BATHTUB

Plumbing Basics: An Essential for When Installing a Bathtub

Plumbing Basics: An Essential for When Installing a Bathtub

Blog Article

Call

We have stumbled upon the article about How to Install a Bathtub Yourself down the page on the net and accepted it made sense to share it with you on my blog.


How to Install a Bathtub Yourself
Installing a bathtub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a new one is also a moderately challenging project. If the old tub is readily accessible, the task can relocate easily; if you need to open a wall surface to remove the old tub and also position the new bath tub, the task is a lot harder. In either situation, the project is within a home handyman's skills, although you will need an assistant to leave the old tub and embeded in the brand-new one. Ensure you have certified yourself for the task and fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is much better to consider using one before you start. Opportunities are you might need an expert plumber to make tube links.
This post will assist you mount a new bath tub in your shower room if you have currently purchased a brand-new tub as well as do not need to transform the arrangement of your previous water system pipelines.
Your tools and also material list need to make up the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to change old faucets with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome because of the restricted access that is commonly the situation.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
    Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Safeguard the tap in place with the producer supplied backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former type ought to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Installing the Bath tub


    Utilizing both wooden boards under its feet, place the tub in the called for position. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four little factors.
    The following objective is to ensure that the bath tub is leveled all round. This can be attained by checking the level and also readjusting the feet on the bath tub up until the level checks out degree.
    To set up faucets, fit the bottom of the furthest flexible tap port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
    Switch on the supply of water and examine all joints as well as new pipework for leaks and also tighten them if essential. Fill the bathtub as well as additionally inspect the overflow electrical outlet and the normal outlet for leakages.
    Finally, take care of the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait till the tub has actually been utilized at the very least when as this will certainly settle it into its final position.

    Preparing for the Installation


    First of all, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to stop pressure on the bath tub.
    Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last position.

    Tiling Around the Tub


    In the location where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
    You can select from a range of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealant can crack relatively early if you do not consider this activity prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof sticky and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    We had been shown that report about Installing A Bathtub from an associate on a different site. So long as you enjoyed our post kindly remember to share it. We thank you for reading our article about How to Install a Bathtub.


    Call, we respond!

    Report this page